Up for sale here is this complete rebuild set for a Pioneer SX-780. This is all the parts you need to rebuild a Pioneer SX-780 main board (the one with the power supply, protection, amplifier section, preamplifier section, and phono EQ), tuner board, and replace the two main caps as well. Over time, capacitors and transistors start acting up and need to be replaced. The old parts are weak and failing. We will make them new again! This kit includes: Main board kit: 45 capacitors10 transistors8 diodes1 relay Tuner board kit: 15 capacitors2 transistors 2 replacement main capacitors (Nichicon VR 10000 uf 50v) These are all high-quality brand new genuine parts. The capacitors are 105° Panasonic FC, Nichicon PW, Nichicon KL, Wima film, and Nichicon VR (for the main caps) capacitors at the same or improved uf and voltage ratings, the transistors & diodes are the correct Fairchild/OnSemi subs for the originals, and the relay is a new Omron relay. These are extremely high-quality parts, and they are what I use when I rebuild Pioneer gear. These are not guaranteed to fix your SX-780, but they will certainly help it run better, and will fix many non-working SX-780s. This kit does not include any fuses, resistors, or the output STK packs. A note about STK packs: The Pioneer SX-780 uses a pair of STK-0050 Darlington Power Packs for outputs–one for each channel. These go bad in so many exciting ways! The receiver could start blowing fuses, it get stuck in protection, it could lose a channel, it could have distortion on one channel, or it could work but just have issues with setting the DC balance voltage, all from STK pack issues. There are tons of STK packs on eBay, and they’re pretty much all modern Chinese fakes. If you are looking for a replacement pack, I would recommend either watching for a used working pull or buying one of the kits where you can replace the STKs with discrete output transistors. The Chinese fakes are cheap, but they will just blow up or break in other fun ways, and you’ll be back where you started. I will include a surprisingly well-written instruction sheet, but this is a moderately complicated rebuild, though it’s not too bad, and you should know what you’re doing and have a decent soldering iron, heat-sink compound, and a dim-bulb tester with a 60W or 100W incandescent bulb. Please see my pictures for details. US shipping and handling is $6, and international is $28. If you want to combine shipping with my other items, just use the “add to cart” feature and then go to your cart and click “request total from seller” and I will send you a combined invoice. If you have any questions, please ask. Looking for more parts? I have power switches, feet, pushbuttons, top case screws, bottom screws, faceplate screws, white LED fuse lamps, blue LED fuse lamps, 6.3v bi-pin bulbs, 8v bi-pin bulbs, 12v bi-pin bulbs, wired 8v 60ma bulbs, new power cords, new main capacitors for the Marantz 1060/2230, wired Pioneer speaker plug replacements, new 630v yellow film capacitors at 13 different values, a large variety of transistors for vintage stereo repair, and more. Just use “add to cart” on everything you want and then check out for combined shipping.
Item Tag: Money Back
-
NEW BELTON 9 pin 12AX7 tube shield micalex socket top mount fits Fender & others
NEW BELTON 9 Pin 12AX7 Tube Socket Fits: Fender and others Actual BELTON product, not an imitation
-
Vintage RCA 12AU7A PLATINUM GRADE Clear Top Preamp Tubes Matched Pair =6189 5814
All tubes come with a full 30 day, unconditional, no questions asked, exchange or money back satisfaction guarantee!Test scores will average between 90% and 95% of NOS values.Individual test scores will be written on the new boxes that you receive with your tubes. These tubes were carefully screened by the manufacturers (Baldwin, Conn, Wurlitzer, Lowery etc.) and specially selected for their low noise and microphonic characteristics. This makes them ideal for your preamplifier and phono stage applications.You are purchasing a “Platinum Grade” matched pair of tubes. This means that the plates are very tightly matched on a calibrated Hickok TV-7 or 799 within 5%Please see our other listings for “Silver, Gold and Platinum Plus” tubes. Silver Grade tubes are matched within 15%, Gold Grade within 10% and Platinum Plus 1%.The Gold and Platinum Grade pairs are recommended for more critical applications such as your preamp and phono stage.To purchase more than one pair, when available, simply change the number in the quantity box which is located just above the advertised price.Please email with any questions and/or concerns.Thank you for viewing my listings.
-
Marantz 4 Plastic Feet w/ Screws Exact Duplicates Of Originals (These are great)
Up for sale here is this set of 4 new reproduction Marantz feet with screws. These are exact replicas of the original feet that were on so many of the 22XX and 42XX receivers. Some of those receivers had feet that were slightly different from these, but these will be great replacements. They will also work on a ton of other gear from Pioneer, Sansui, Sony, etc. If your Marantz has a wood case that covers the bottom, you will need feet with longer screws, which are available here. These are incredibly high-quality Made in USA feet. They are made from incredibly strong BASF A3W Nylon 6/6 material, and the screws are extremely high-quality as well. I personally use these feet on tons of Marantz receivers–they are incredible. These measure 26.5mm OD (1.04″) x 18.5mm H (.73″). Please see my pictures for details and measurements. US shipping and handling is $5, and international is $18, no matter what quantity you buy. All my small parts are set up for combined shipping, so just use the “add to cart” feature and then check out all at once, and it will combine shipping. If you have any questions, please ask. Looking for more Marantz parts? I have power switches, recap kits, pushbuttons, top case screws, bottom screws, faceplate screws, white LED fuse lamps, blue LED fuse lamps, 6.3v bi-pin bulbs, 8v bi-pin bulbs, 12v bi-pin bulbs, wired 8v 60ma bulbs, and more. Just use “add to cart” on everything you want and then check out for combined shipping.
-
2 Pioneer Speaker Plug Connectors SX-525 SX-626 SX-727 SX-828 SX-990 SX-1000
One pair of quality reproduction plugs for speaker wire connection to Pioneer, Akai and Allied Radio Shack receivers. Customized in our shop for a perfect fit, these plugs have brass conductors with screw terminals for maximum signal transfer. No soldering required. Free same day shipping if ordered before 3:00 PM Eastern Time. These plugs fit the following amplifiers, receivers, components: Compatible PIONEER Models: H Series 8-Track Receiver: H-555, H-802, H-803, H-7000, H-R9000 K Series: K71-032, K71-642, K72-007 QA Series: QA-800 QM Quadraphonic: QM-800A SA Series: SA-100, SA-302, SA 302R, SA-500, SA-500A, SA-600, SA700, SA-800, SA-900, SA-1000 SX Series: SX-300T, SX-400, SX-410, SX-424, SX-440, SX-525, SX-626, SX-700T, SX-727, SX-770, SX-820, SX-828, SX-990, SX-1000, SX-1000TD, SX-1000TW, SX-1500, SX-1500T, SX-1500TD, SX-2500, SX-3000, SX-6000, SX-9000 QX Series: QX-4000, QX-8000, QX-9000, QX-9900 Compatible AKAI Models AA Series: AA-910, AA-920, AA-930, AA-940, AA-960, AA-970, AA-980 AS Series: AS-980 Compatible ALLIED Radio Shack Models: 335, 339, 365, 380, 395, 399, 429, 435, 445, 490, 498, 475, 495, 995 Package contains one pair (2 plugs). International Buyers: Import taxes are the buyer’s responsibility. If such taxes are not added when you make your purchase, you may be responsible for them upon receipt of your package, depending on the laws of your country. You will not be charged twice for taxes.
-
10 New Warm White 8V Fuse Lamp LED Light Bulbs Marantz 360-DEGREE No Hot Spots!
Up for sale here is this set of 10 (ten) new 8v snap-in warm white LED fuse lamps. These are MUCH different, and much higher-quality, than the normal 3-LED fuse lamps that are all over eBay. These are custom-made and are 360-degree lamps, with a plastic cover to help diffuse the light perfectly. They will give you a nice even glow for your Marantz equipment. They are not as aggressively bright as the 3-LED bulbs. I have these available in warm white, cool white, cool blue, and emerald green. These are slightly directional, so you may want to rotate them a little for the absolute best look. Specs:Type: LEDColor: Warm WhiteLength: 30mmDiameter: 6.1mmPolarity: Non-polarVoltage: 8v AC/DCCurrent Draw: 20mA These are perfect for replacing any of the 8v fuse lamps found in vintage gear by Marantz, Pioneer, Sansui, Kenwood, and more. These are 30mm long and will fit nicely in the old holders. LEDs run cooler, last almost forever, and draw much less current than the old incandescent bulbs. These are brand new bulbs and are guaranteed to work great for you. I have other bulbs listed, so if you need those, take a look at my other listings. Please see my pictures for details. One picture shows how these look in a typical Marantz receiver. US shipping and handling is $5, and international is $18, no matter what quantity you buy. All my small parts are set up for combined shipping, so just use the “add to cart” feature and then check out all at once, and it will combine shipping. If you have any questions, please ask. Looking for more parts? I have power switches, feet, pushbuttons, top case screws, bottom screws, faceplate screws, white LED fuse lamps, blue LED fuse lamps, 6.3v bi-pin bulbs, 8v bi-pin bulbs, 12v bi-pin bulbs, wired 8v 50ma bulbs, new power cords, new main capacitors for the Marantz 1060/2230, wired Pioneer speaker plug replacements, new 630v yellow film capacitors at 38 different values, new 1200v yellow film capacitors at 15 values, a large variety of transistors for vintage stereo repair, new Wima film capacitors for stereo repair, new 250v yellow film crossover capacitors, and more. Just use “add to cart” on everything you want and then check out for combined shipping.
-
Vintage Vacuum Tube Grab Bag – NOS IN BOX – 3 TUBES FOR A BUCK! Thousands Avail!
GRAB BAG OF NOS Vacuum Tubes (each qty 1 you purchase gets you three tubes, in boxes)What you will get:For every lot you purchase, you will receive 3 vintage vacuum tubes in boxes. While this lot will not contain any valuable vintage tubes (likely no Western Electric, 12ax7, Genelux, etc…), but it will contain all vintage tubes. There will be a good assortment of tubes, audio tubes, 7/9 pin, octal/loctal, early tubes and more. Many lots are available! (please understand the picture in the listing is representative, and not the exact lot you are getting…)Use them for resale, stock up for your inventory, art projects, collect them etc!—————These are not tested tubes – while they are NOS in boxes, sometimes after sitting 50+ years they no longer work – please expect that 5-10% of the tubes may test bad. However, 90%+ of these tubes are functioning as new!Please let me know if you have any brand preference – however, there is no guarantee we will have any specific brand in stock.
-
Marantz 2270 COMPLETE REBUILD KIT Transistors Relay Main Filter Capacitors Recap
Up for sale here is this complete rebuild kit for a Marantz 2270. This contains new capacitors and transistors for all the boards, including the tuner boards, and includes correct-size replacements for the two main capacitors and a new relay. Each board’s parts are in a separate bag for ease of installation. Replacement transistors and diodes are included for the non-tuner boards. This kit does NOT include the following: Lights (available here)AC fuse or any other fusesany resistorsoutput or driver transistors (correct replacement outputs are MJ21195G/MJ21196G, available here. Specifically, you will receive: 2 main capacitors (Nippon Chemi-Con 10000 uf 80v) P150 AM board: 13 capacitors (Nichicon PW) P300 MPX board: 17 capacitors (Nichicon PW, Wima film) P400 Preamp board: 13 capacitors (Nichicon PW, Wima film)8 transistors (Fairchild/Onsemi) P500 FM board/P550 muting board/meter capacitor: 10 capacitors (Nichicon PW, Wima film) P700 phono EQ board:3 capacitors (Nichicon PW, Nichicon KL)6 transistors (Fairchild/Onsemi)4 diodes (Onsemi) P750 amplifier boards: 8 capacitors (Nichicon KT, Panasonic film)14 transistors (Fairchild/Onsemi, 4 hfe-matched for differentials)1 piece of heat-shrink tubing P800 Power Supply Board kit:8 capacitors (Panasonic FC, Nichicon PW)7 diodes (Onsemi)4 transistors (Fairchild/Onsemi)1 Relay (Omron) Capacitors are generally the same capacitance (except a few that go higher for improved filtering) and the same or higher voltage ratings. Transistors and diodes are the correct Fairchild/Onsemi subs for the originals. These are all extremely high-quality parts and are the same parts I use when I rebuild Marantz gear. I have rebuilt at least 1-2 dozen Marantzes in the last year. I will include surprisingly well-written instructions, but this is a fairly complicated rebuild, and you should know what you’re doing and have a decent soldering iron, a decent desoldering iron, heat-sink compound, and a dim-bulb tester. Please see my pictures for details. US shipping and handling is $10, and international is $28. If you have any questions, please ask. Looking for more parts? I have power switches, feet, pushbuttons, top case screws, bottom screws, faceplate screws, white LED fuse lamps, blue LED fuse lamps, 6.3v bi-pin bulbs, 8v bi-pin bulbs, 12v bi-pin bulbs, wired 8v 60ma bulbs, new power cords, new main capacitors for the Marantz 1060/2230, wired Pioneer speaker plug replacements, new 630v yellow film capacitors at 13 different values, a large variety of transistors for vintage stereo repair, and more. Just use “add to cart” on everything you want and then check out for combined shipping.
-
10 New Warm White 8V 300ma Incandescent Wedge Lamp Light Bulbs .3A 0.3A
Up for sale here is this set of 10 new 8v warm white 8v 300mA incandescent wedge lamps. These are great bulbs! I have other bulbs listed, so if you need those, take a look at my other listings. Specs: Type: Incandescent Color: Original (warm white) Diameter: 9.6mm Height: 24.4mmPolarity: Non-polarVoltage: 8v AC/DC Current Draw: 300mA (0.3A) Please see my pictures for details. US shipping and handling is $5, and international is $18, no matter what quantity you buy. All my small parts are set up for combined shipping, so just use the “add to cart” feature and then check out all at once, and it will combine shipping. If you have any questions, please ask. Looking for more parts? I have power switches, feet, pushbuttons, top case screws, bottom screws, faceplate screws, white LED fuse lamps, blue LED fuse lamps, 6.3v bi-pin bulbs, 8v bi-pin bulbs, 12v bi-pin bulbs, wired 8v 60ma bulbs, new power cords, new main capacitors for the Marantz 1060/2230, wired Pioneer speaker plug replacements, new 630v yellow film capacitors at 13 different values, a large variety of transistors for vintage stereo repair, and more. Just use “add to cart” on everything you want and then check out for combined shipping.
-
5U4GB GA VINTAGE TUBE – RCA, RAYTHEON, CBS, SYLVANIA, & ETC. – TESTED
PRICE IS FOR ONE TUBE, MANY ARE AVAILABLE. WILL TRY TO ACCOMMODATE REQUESTS FOR SPECIFIC BRANDS, PLEASE UNDERSTAND AS THEY SELL SOME MAY NOT BE AVAILABLE.PLEASE BE AWARE THAT THE PICTURE MAY NOT HAVE THE TUBE THAT YOU ARE PURCHASING, WE ARE ALWAYS ADDING NEW INVENTORY. ALL ARE GOOD, QUALITY TUBES, WITH PLENTY OF LIFE LEFT! US SHIPPING: $4.75 FOR THE FIRST TUBE, 70 CENTS EACH ADDITIONAL.GLOBAL SHIPPING: $19 FOR THE FIRST TUBE, $1 EACH ADDITIONAL TUBES ARE GUARANTEED VINTAGE, NO RE-ISSUES, ALL ARE ORIGINAL VINTAGE VACUUM TUBES TESTING STRONG.PLEASE READ THE FOLLOWING!SHIPPING & HANDLING I take great pride in my shipping. I wrap my tubes in bubble wrap. Then place them into a strong cardboard shipping box, with good tape. I ensure that your tubes will make it to you safe and sound. If they do not, I will work with you to make it right. I add very little for handling fee’s within my shipping charge. Shipping is not where I make money. Let me quickly divulge my costs. The USPS First Class mail keeps going up, up, up. A standard shipment (up to about a half dozen tubes) now costs ME $2.77 – $3.50 from the post office. Large orders can cost me considerably more. I pay about 40 cents per box, and then another 50 cents for printer, tape, bubble wrap, etc. costs. That means that the average shipment costs me around $3.50. Now, eBay and Paypal also charge me about 12% combined for shipping costs. So, if I charge $4.50 for shipping, they take 54 cents! That puts me at about 20 cents over for a standard shipment. That pays for my gas, etc to/from post office. If you order more than 1 or 2 tubes, I am spending another 25 cents or more in bubble wrap… putting me even or slightly at a loss. I do not short change on materials for shipping. I simply do not use inferior materials. I’d rather have you return an item because you didn’t like the sound than because it was broken.Combined Shipping Yes! I combine shipping! However, it is super complex to combine shipping automatically on tubes, as some of the little tubes can be added at no additional cost, but some of the bigger output/transmitter tubes will be charged additional. The best way to do it is to buy the items, and request an invoice before paying (eBay only lets you request an invoice after purchasing). If eBay charges immediate payment, I will provide a refund when I ship it. I generally add 20-30 cents per transaction after the first, depending on the size of the order, the types of tubes, metal vs. glass tubes, etc. Feel free to contact me prior to purchasing as well.Best Offers I generally consider Best Offers as a good mechanism to make offers on multiple tubes, or for higher priced items – while I will respect and respond to each offer, if you make an offer for a super low price, please understand why I cannot accept. I am running a business here, with electricity costs, warehouse lease, computers, printers, office supplies, internet connection, etc. An offer for $2.50 for a $15.00 item will likely be declined.Returns I accept a 30-day money back return on all my items, unless the item description states otherwise. On some tubes, for example, those I cannot test – or test bad (display tubes), I will not accept returns. But for 99.99% of the tubes I sell, feel free to try them out and make sure you like them. If you do not like the tube, and would like to return, please do so within 30 days. Buyer to pay shipping both ways, unless the item is significantly different than described/pictured.Testing I can test about 99.99% of the tubes I sell. I have currently calibrated vintage and modern testers (Triplett, Hickok and B&K as well as the MAXI Preamp and Power Tube Testers). I generally state which tester was used. Sometimes, these testers test at different currents or biases than your tester. Testing results can vary from tester to tester. NOS I sell many NOS (New Old Stock) tubes. This means that the tube is new (as far as I can tell from a visual inspection) and has never been put into service. I test many NOS tubes prior to listing – see description for details. If the tube does not have any mention of being tested, please assume the tube is in good working NOS order. I may not have tested it, but if it arrives less than NOS (or shorts/leaks, etc), please return for full refund.Questions? Please refer to the description, return policy, shipping policy and most importantly – the picture(s). Pictures are a vital part of the description. They can contain many of the details you may ask about (tube codes, date codes, getter type, plate color, etc.). If you cannot find the info you are looking for, please contact me.